AC 220V, No Power Supply, No Breakout Board,  Easy to wire

Following items are included: EL7 Series driver and motor

-- 1 Pc EtherCAT Servo Motors  750W

Model Number:  ELM2H-0750LA80F

Motor Specification:

• Rated voltage 220VAC, rated power 750W
• Frame 80mm, rated torque 2.39N·m, rated speed 3000r/min
• 23-bit optical encoder
• No brake, direct connector
• Strong overload capacity
• IP67

• Shaft diameter: 19 mm (0.748")

• Shaft extension length: 35 mm (1.378")

• Keyway width: 6 mm

• Shaft end thread: M5 × 15 mm

-- 1 Pc EtherCAT Servo Driver

Model Number: EL7-EC750F

If you would like to order the Servo Motor Control kit with cable, following cables are included.

You can choose either 5 Meter or 3 Meter length:

-- 1 Pc Cable-7BMA5M0-Z "5-Meter encoder cable with battery"

-- 1 Pc Cable-RZ5M0-S - 5-Meter power cable

Or

1 Pc Cable-7BMA3M0-Z "3-Meter encoder cable with battery" ,

1 Pc Cable-RZ3M0-S - 3-Meter power cable

Read the rest of this entry »

KL23H2100-50-4BM:

NEMA 23 Frame

570 oz in.

dual shaft ( Front Shaft 1/4", rear shaft 1/4")

1.8° /200 Steps Per Rev.

5 Amps Current Per Phase

4-Wire  Bi-polar,

3 pound 10 oz

BLACK TO A+

Drawing Download:

KL23H2100-50-4BM (7489 downloads)

Torque Curve:

KL23H2100-50-4BMT (1175 downloads)

This one will replace the KL-5056D

• Multi-Stepping allows a low resolution step input to produce

a higher microstep output for smooth system performance

• Microstep resolutions programmable, from full-step to 51,200 steps/rev

Can be set by Dip switch (2,4,8,16,32,64,128,256,5,10,25,50,125,250)

• Supply voltage up to +50 VDC

• Output current programmable, from 0.5A to 5.6A(Can be set by Dip switch too)

• Pulse input frequency up to 400 KHz

• TTL compatible and optically isolated input

• Full or Half Current , Sw4: Off= Half Current

• Suitable for 2-phase and 4-phase motors

• Support PUL/DIR and CW/CCW modes

• Over-voltage, Over-current, phase-error protection

One Year Warranty

Wiring:

Digitaldriverwiring (21202 downloads)

Manual:

KL-5056E User Manual (3004 downloads)

Motion Controllers

M31 Factory-Certified Controllers  

Compatible Controllers

• Warp9: ESS

Advanced Microstepping Stepper drive, DM805-AI

• Extra-low motor noise offers excellent quietness
• Analogue signal (0-5V) for speed control
• Step & direction control signals also acceptable
• Internal step generator for no motion controller system
• Built-in 5V output for an analogue control and testing
• Built-in potentiometers for speed, acceleration and deceleration adjusting
• Limit signal input for safe operation
• Anti-resonance and low-speed ripple smoothing
• Supply voltage up to 80 VDC
• Output current programmable, from 0.5A to 7.0A

Electrical Specifications

Velocity Control

  Operating Environment

Manual & Download:

DM805-AI (767 downloads)

One Year Warranty

Brand New in the box, 900 Watt / 1.2 HP, KL-900-12-901

Voltage: 12VDC Current

No load Max Current : 25 Amps

No load Speed:  43 RPM at the output shaft

90:1 Gear Ratio

Load Torque: 50 N.M

Load Speed: 38 RPM

with chrome cover and mounting hardware!

Sealed gearbox and drive shaft

A 5-hole mounting pattern

Works with the 3-hole and 4-hole mountings

2 hole shaft for most drop in replacement.

Standard shaft Length 3”

Diameter 0.75”

One year Warranty

Drawing:

KL900-12-901 (873 downloads)

Torque Curve:

KL900-12-901T (869 downloads)

USB MOTION CONTROLLER for MACH3, MACH4, UCCNC software

Windows 2000, Windows XP, Windows Vista, or Windows 7 , Window 10 , Operating System will be ok ( 64Bit or 32bits)

Include: 1pcs UC-100, 1pcs USB cable

USB cable: 1.8 meter  long

If you need the Gender Changer, click the link and add

DB25 MALE TO DB25 MALE M/M Mini Gender Changer Coupler

Features:

- Very Easy to connect to the existing mach3 DB25 Breakout board or any new DB25 breakout Board.

- Controls up to 6-axis simultaneously.

- Works with Mach3, Mach4 , UCCNC software via plugin.

- Upto 100kHz operation.

- USB connection from your PC to DB25 controller.

- Same pinout as a standard LPT port.

- Fast communication with data buffer for robust and stable operation.

SPECIFICATIONS:

- Automatic firmware checking and firmware update.

- Motion control on upto 6-axis (X, Y, Z, A, B, C).

- Configurable maximum stepping frequency, the options are 25kHz(with 20usec pulse

length), 50kHz(with 10usec pulse length), 100kHz(with 5usec pulse length).

- On the fly configurable 12 pieces of 5Volt (TTL level) buffered outputs. The current

sink/source capability is 20mA max. per output.

- On the fly configurable 5 pieces of 5V (TTL level) schmitt triggered and filtered inputs.

The input internal pullup resistance to 5Volts is 4.7kOhms.

- About 1 second long communication buffer.

- 100% LPT port compatible pinout.

FEATURES

- Reference inputs.
- E-stop input.
- Softlimits.
- Limit switch inputs.
- Limits override.
- Index input (extended function supports multi slot sensors).
- Spindle speed PWM control output.
- Step and direction spindle control output.
- Spindle and coolant relay control.
- Charge pump safety signal output (configurable to active/inactive when in E-stop).
- Charge pump adjustable frequency (12.50kHz in normal or 5kHz in laser mode).
- All signals configurable to active High/Low.
- General purpose I/O signals handling.
- Offline mode.
- MPG1 and MPG2 support.
- Slave axis.
- Backlash compensation.
- Digit/probe input.
- THC control inputs.

Product Manual& Downloads

Userguider (10946 downloads)

if you do not have mach3 software, you can use this software too ,

Click for UCCNC software. This software works great

Click to order mach3

Click to order mach4

Click for USB MOTION CONTROLLER for Mach3 plugin

UC100 Troubleshoot for Window 10 or 11:

Click for UC100 Troubleshoot

We are an authorized dealer.

Mach4 CNC Controller Software,

(pls email us the PCID , so we can email you the license file)

Follow this instruction and send us the PCID: Mach4 Installation Guide (1121 downloads)

We will email you the license.   No refund after the license is emailed.

you need a USB or Ethernet Smoothstepper, click the following link:

6 Axis USB MOTION CONTROLLER for Mach3, Mach4 UC100, or UCCNC (USB UC100)

Ethernet SmoothStepper Motion Control Board for Mach3 and Mach4, 6 Axis (with cables)

Mach4 with ESS connection, Download tutorial here

Mach4 setting tutorial (2519 downloads)

Mach4 Setup (3818 downloads)

IMPORTANT NOTE:

The LICENSE will only work for the Computer for which you supply the PC ID at checkout. Each PC has a unique ID code and the license works in coordination with this code.

Pls send us the PC ID after you install Demo

• Download
• Manuals
• Mach4 New Version

About the Demo: The purpose of this Demo is to give users a look at Mach4 Hobby and the ability to test the screen designer. The screen designer will be nearly identical in all versions of Mach4 and this version allows for the layout of GUI’s. Scripting examples will be included in the next Demo. Many Motion control plug-ins (software driver for motion control boards) are not 100% complete. We are working with many different groups to help them complete and test their plug-ins for Mach4. A version with motion control will be released depending on the time to make improvements from the feedback received from this version.

Mach4 Information: Mach4 is our newest version of CNC motion control software. While the core software is completed, it will take time to complete the software plug-ins that allow Mach4 to communicate with specific hardware devices. OEM’s and equipment manufacturers that have committed resources to developing their software plug-ins, will be the first to take advantage of Mach4’s benefits. Much of the development of the plug-ins is completed by the manufacturer of the hardware.

Mach4 is completely new software and has less than 1% of the programming code in common with Mach3. It was written from the ground up to be expandable, flexible, and extremely responsive for use with very large files on any operating system; including Windows, Apple, and Linux. While there was only one version of Mach3, Mach4 will be offered in different versions (not including the many customized OEM versions).

Please read the tabs below for more information.

Screen Shots of the Standard Mach4 Hobby User Interface. Tab controls are used in Mach4 to switch quickly between different screens. Users may modify the standard screen or create a new tab that contains the buttons, graphics, and indicators they need.

you need a parallel port  or other plugin plugin to run motion.

AXBB-E Ethernet Motion Controller and Breakout Board Combined Controller

Features:

- Complete motion controller and breakout board solution in a single board.- 8 optically isolated high speed N-channel power mosfet transistor outputs.(NPN)- 9 non-isolated buffered TTL outputs to control step/dir signals, laser driver etc.

- Isolated charge pump output with power N-channel mosfet transistor.

- 6 high speed optoisolator inputs.

- 1 IDC26 non-isolated extension port with standard LPT port pinout (12 outputs and 5 inputs).

- LED indicators on isolated I/Os.

- Isolated I/Os are 24Volts capable.

One Year Warranty

You can purchase with UCCNC, MACH3, or MACH4 software, we will email the license key:

UCCNC

MACH3

MACH4

Downloads for this product:

1.) Product manual

2.) UCx00 automatic installer application for Mach3

KL-34GH51PS 5:1 Helical Planetary Gearbox

Ratio 5:1

Nominal Output

Torque 50NM

Max Output Torque 100NM

Average Input Speed 3500r/min

Max Input Speed 6000r/min

Frmax. For 10000h 450N

Famax for 10000h 430N

Backlash < 7  arcmin

Average Lifetime < 20000h

Noise < 60 db

Motor Shaft input 1/2"

Output Shaft:  1/2"

Download Drawing:

KL-34GH51PS (523 downloads)

Helical PLANETARY GEARBOX WITH STEPPER MOTOR, REDUCE THE SPEED, INCREASE TORQUE, PRECISION, MAINLY USED FOR CNC ROUTER, CNC PLASMA,CNC LASER, MANY OTHER AUTOMATION SYSTEM

CANopen Communication:

• Link Layer Protocol: CAN Field-bus.
• Application Layer Protocol: CANopen Protocol.
• CAN-ID Type: CAN 2.0A.
• Communication Rate : 1M/500k/250k/100k/50k/20k bit/s.
• Sub-protocol: DS301 V4.02 , DSP 402 V2.0.
• PDO Transmission Modes: Time trigger/event. trigger/asynchronization/synchronization.
• Control Mode: Profile position, Profile velocity , Profile torque, homing.

Basic Specification:

• Frame Size: 60mm
• Voltage Input: 24-70Vdc
• Encoder: 17bit incremental
• Motor without brake
• 2.5 – 3 times overload
• 4 programmable input
• 2 programmable output
• RS232 for configuration

Part Number                             KL-7028CO
Rated Power(W)                               400
Rated Torque(Nm)                           1.27
Peak Torque(Nm)                             3.81
Rated Speed(rpm)                             3000
Peak Speed(rpm)                               4000
Rated Voltage(Vdc)                           48
Weight(kg)                                           1.25
Inertia(Kg.cm2)                                  0.58
Torque(Nm/A)                                    0.127
Input Voltage(V)                                24~70
Continuous Current(Arms)                10
Peak Current(A)                                    28
Logic Signal Current(mA)                   10
Isolation Resistance(MΩ)                   100
Protection Level                     IP54 for motor, IP20 for drive

Downloads:

400W CANbus Integrated Servo Motor Drawing (699 downloads)

400W CANbus Integrated Servo Motor Manual (1005 downloads)

One year warranty

KL-2200 spindle with 4 Bearings

OD=80 mm

Length =215 mm

Voltage:  220V

Speed: 8000-24000 R/min ( run speed at 60% or less than 80% of rated Max spindle)

Power: 2200 W (3HP)

Frequency: 400 Hz

Water Cooling,

ER20 Collet chuck. (But tool is not included: you can use 1/16", 3/32", 1/8", 3/16", 7/32", 1/4", 5/16", 11/32", 3/8", 13/32", 7/16", 1/2" )

Grease Lubrication,

Runout off: less than 0.005mm

Water cooling about 20-26 gal/hr

about 15 ibs

One year manufacture warranty

Use this VFD:

2.2KW (3HP) VFD for Spindle (KL-VFD22) 220VAC Input  for 220V spindle

You can use this water pump and tube for the spindle:

Water pump for spindle

PVC tube for spindle

Manuals & Downloads

KL-2200 (9570 downloads)

KL-2200 Spindle Performance Curve Sheet (793 downloads)

Ethernet SmoothStepper Setup Video

SCU (System Configuration Utility)

SCU (System Configuration Utility)

6 Axis Ethernet SmoothStepper Motion Control Board for Mach3 and Mach4, with Relay and Spindle control C11G

Click this C11G Wiring Video

If you use these 2 items:

1: CNC 6 axis Breakout Board with Relay and Spindle Control, C11G

CNC C11G 6-Axis Interface Breakout Board with Relay and Spindle control

2: A CNC 6 axis Ethernet SmoothStepper Motion Control Board for Mach3 and Mach4

Ethernet SmoothStepper Motion Control Board for Mach3 and Mach4, 6 axis (Ethernet SmoothStepper Motion Control Board for Mach3 with cables )

Use this 12V/2A with 5V/2A power supply: KL-30A

If you do not use the Spindle Relay Control, you need to order this power supply:

5V/3A power supply

Click this C11G Wiring Video

Wiring:  C11G Wiring (1993 downloads)

Ethernet SmoothStepper (14519 downloads)

To replace:

(3-Axis Motion Control Card USB2.0 Interface, CNC MACH3 USB Card XHC-MK3, or 4-Axis Motion Control Card USB2.0 Interface, CNC MACH3 USB Card XHC-MK43 Axis CNC USB Card Mach3 200KHz Breakout Board,3 Axis CNC USB Card Mach3 200KHz Breakout Board, 4 Axis CNC USB Card Mach3 200KHz Breakout Board)

iSV2-RS8675V48H with 2 meter cable

Main power voltage: 24-60VDC.

Rated voltage: 48VDC

86mm frame size with 12.7mm shaft

Rated power: 750W.

Rated torque: 2.39N.m.

Overload: 300%

17 bit incremental magnetic encoder

Pulse, Direction control

Modbus RTU over RS485. Build-In 16 PR paths

Dip switch for node ID, baud rate and terminating resistor

RS-232 serial interface for easy tuning with Motion Studio

iSV2-RS8675V48HDrawing (495 downloads)

Acorn CNC Controller with Ethernet, Free Centroid  Software

(Set IP Address: 10.168.41.1,  Subnet Mask: 255.255.255.0)

Acorn kit includes Centroid "Free" CNC Mill and Lathe CNC software!

Centroid Acorn SainSmart Relay Module adapter kit :

Link to the Acorn documents for your reference.

Link to the Tech Sheet for the new Acorn Relay Module kit for your reference.

Centroid Acorn CNC controller kit (part # 14455) includes:
- Acorn_REV4 CNC control board
- Acorn Plug and Play Relay Relay Module
- Dual power 5 VDC and 24 VDC logic power supply
(50/60 Hz 100-120 VAC OR 208-240 VAC input power)
- Logic power supply hookup leads
- 110 VAC power cord
- 15’ Shielded Ethernet cable
- Centroid CNC12 "Free" CNC Mill and Lathe software download
- Touch Screen Responsive Operator Controls
- DIY self  service CNC support thru Centroid Community CNC Forum which is Centroid   Technician monitored and maintained.

Wiring Diagram & Downloads

Acorn CNC Controller Wiring Diagram (1239 downloads)

Bonus! Acorn Relay Module now included with all Acorn CNC controller kit orders

Plug and Play Relay Outputs with the Acorn CNC Relay Board! Direct connection to the Acorn board with the supplied ribbon cable makes connecting and getting a relay board up and running a 5 second operation. The Plug and Play relay module allows CNC controlled connections to various CNC devices such as VFD’s, solenoids, lights, fans, pumps, motors, other larger relays and contactors in a compact format. The 8 relay module contains eight SPDT (Single Pole Double Throw) high current relays (10 AMPS at 250 VAC,and 10 amps at 30 VDC) which can directly control any device rated at or below the maximum rating of the relays. If higher current devices are required these relays can then in turn control larger relays or contactors to control the higher current device! Relay module has on board LED indicator lights for each relay

(Note: A 1920x1080 wide screen LCD Display is required and a Touch Screen is recommended.)

1.) The PC CPU must have a SINGLE CORE minimum benchmark of 1500.  You can look up a CPU’s benchmark # using this web site.

http://cpubenchmark.net/singleThread.html  

Notice that this is the “Single Thread” benchmarks chart.
Using a CPU with a single thread  benchmark rating higher than 1500 is required

2.) While not required...it is highly recommended to use a SSD (solid-state drive)  We only recommend Intel or Samsung SSD’s

3.) minimum 4 Gig’s of Ram

4.) Windows 10 that is configured for CNC control use see Step 2 below.

5.) Ethernet port

6.) An LCD monitor with a 16:9 aspect ratio

Free Centroid Software download
Acorn CNC Controller Specifications Manual

Centroid Acorn CNC Control System or  Better Than Mach3 or Mach4

Centroid Acorn CNC Basics

Centroid Acorn CNC Basics - Win 10 PC Setup and benchtest

Power and Ethernet to the Acorn CNC control board

Bench Test Running Motors

A Closed Loop Stepper Driver Test

Centroid Acorn CNC Discuss Forum

Acorn CNC controller Hookup Schematics

Link to set up

https://grok.lsu.edu/article.aspx?articleid=19320

• Cost effective high quality EtherCAT Solution
• Interfaces with Mach4 through plugin
• Free EtherCAT PC Software EC-Link for easy configuration
• Built on proven and reliable Platform
• Import ESI files for different devices
•  EtherCAT controller will support Mach4 Software via the reliable and proven Mach4 plugin.
• +12 - 28VDC (Polarity Protected)

EtherCAT Drives Tested

• Mitsubishi MR-JET, MR-J5
• Omron 1S series
• Delta ASDA-A2
• Advantech AMAX I/O Block
• Maxine EP3E-EC
• Beijing CTB Technology 3-Axis Drives
• Yaskawa SGD7S
• LeadShine EM3E-A882

·8 Digital Inputs NPN Optical Isolated

This kit includes:

1:  2.2KW (3HP) VFD FOR SPINDLE (KL-VFD22-110V) 110VAC INPUT

Input: 110VAC ±20%  1 or 3 Phase (R,S or R, T or S,T)    50/60Hz

Output: 110VAC 3 Phase (U,V,W)   2.2KW

(U,V,W) Frequency Range: 0.5-400Hz

0-10V Analog interface capability

Variable speed

2: KL-2200 2.2KW Spindle 110V 

OD=80 mm

Length =215 mm

Voltage: 110V

Speed: 8000-24000 R/min ( run speed at 60% or less than 80% of rated Max spindle)

Power: 2200 W (3HP)

Frequency: 400 Hz

Water Cooling,

ER20 Collet chuck. (But tool is not included: you can use 1/16", 3/32", 1/8", 3/16", 7/32", 1/4", 5/16", 11/32", 3/8", 13/32", 7/16", 1/2" )

Grease Lubrication,

Runout off: less than 0.005mm

Water cooling about 20-26 gal/hr

about 15 ibs

VFD Parameter Set:

PD000=0 for Parameter unlock ( 1 ) for Parameter Lock

PD001=0 (1 For Remote Control)

PD002=0 ( 1 For 0-10v Terminal Control or Remote Trim Pot Control )

( J1 Also Needs to be set for Terminal Control)

PD003=400

PD004=400

PD005=400

PD007=20

PD008=110 (Motor Rated Voltage, If you have 220v spindle then set to 220v )

PD009=15

PD010=8

PD011=120 ( 100 Minimum Setting with Quality VFD, 120 is Safe)

PD13= 08 is for Factory reset, Only use this to set VFD to Factory Default SettingsPD014

Acceleration = 12 ( Adjust to suit)

PD015 Deceleration=12 (Adjust to suit) ( PD15 is ignored IF PD26=1 Then the Spindle will

Coast to a Stop)

PD141=110 ( Motor Rated Voltage ) (220 for VFD Rated for 220v )

PD142= ( Motor Max Amps)

PD142=( 220v Set for your motor Amp Rating 2.2Kw Spindle

9 amp )

PD142=( 220V Set for your motor Amp Rating 1.5Kw Spindle 7 amp )

PD142=( 220v Set for your motor Amps Rating 800w Spindle 4 amps )

PD142=( 120v Set for your motor Amp Rating 800w Spindle 7 amp )

PD143=2 ( Motor Number of Poles)

PD144=3000 (Max Motor RPM) =3,000= (24,000)

PD70=0 ( This may need to be set to 1 if Control Voltage is 0-5v )

PD72=400

PD73=120 ( 100 Minimum Setting )

If you have E. Lv. S error code alarm

Pls set

PD200=65535

PD209=70

You can use this water pump and tube for the spindle:

Water pump for spindle

PVC tube for spindle

Thanks to our customer.

click here for video by cuttingtooldesigner

One year manufacture warranty

Download:

Software and Plugin Download

(This kit is not EtherCAT kit, check this link for EtherCAT Kit: 750W EtherCAT Kit)

AC 220V, No Power Supply, No Breakout Board,  Easy to wire

1: 750W 2.4NM AC Servo Motor,  Driver Kit without Cables;

• AC Servo Motor  ELM0750LH80F-SS
• AC Servo Drive  ELP-D750Z

2: 750W 2.4NM AC Servo Motor,  Driver Kit with Cables;

• AC Servo Motor  ELM0750LH80F-SS
• AC Servo Drive    ELP-D750Z
• Power cable (Optional length)
• Encoder cable (Optional length)

Rated Voltage(Vac): 200-220
Rated Power(w): 750
Rated Torque(N.m): 2.4
Peak Torque(N.m): 8.36
Rated Speed(rpm): 3000
Peak Speed(rpm): 6500
Rated Current(Amp): 5.1
Peak Current(Amp): 17.8
Torque Const(N.m/Amp): 0.465
Back EMF Const(V/krpm): 28.8
Resistance(Ω): 1.00
Inductance(mH): 5.8
Inertia(kg*m2*10-4): 1.56
Poles: 10
Radial(N): 392
Thrust(N): 147
Encoder type: 23bit absolute
Protection level: IP65

*One Year Warranty*

Downloads:

AC Servo Motor  ELM0750LH80F-SS Drawing (888 downloads)

ELP AC Servo Driver User Manual (1350 downloads)

AC 220V, No Power Supply, No Breakout Board,  Easy to wire

Following items are included: EL7 Service driver and motor

A: 1 Pc EtherCAT Servo Motor 1000W

Model Number:  ELM2H-1000LA80F

Motor Specification:

• Rated voltage 220VAC, rated power 1000W
• Frame 80mm, rated torque 3.18N·m, rated speed 3000r/min
• 23-bit optical encoder
• No brake, direct connector
• Strong overload capacity
• IP67

• Shaft diameter: 19 mm (0.748")

• Shaft length: 35 mm (1.378")

• Keyway width: 6 mm

• Shaft end thread: M5 × 15 mm

B: 1 Pc EtherCAT Servo Driver  190-240VAC

Model Number: EL7-EC1000F

• Servo drive with power rating from 400W to 2000W
• User-configurable I/Os: 4 DI, 3 DO, spring plug I/O port and 2 high speed touch probe input
• Equipped with internal regenerative resistor
• Position, velocity and torque loop control
• Servo functions including model following control (MFC), vibration suppression (Mechanical resonance and end vibration), friction compensation and auto gain adjustments
• Matching motors with power rating from 50W to 1000W
• Motors with 23-bit magnetic/optical encoders
• Optional holding brake

*If you would like to order the Servo Motor Control kit with cable, following cables are included.*

-- 1 Pc Cable-7BMA5M0-Z "5-Meter encoder cable with battery"

-- 1 Pc Cable-RZ5M0-S - 5-Meter power cable

Or

1 Pc Cable-7BMA3M0-Z "3-Meter encoder cable with battery" ,

1 Pc Cable-RZ3M0-S - 3-Meter power cable

If you need the Mach4 license, check the link:

Fully Licensed versions of Mach4, Email you the license.

Check the link to see Video

EtherCAT Video for Maho CNC Conversion from Tony (65)

EtherCAT Video (365)

*One Year Warranty*

Downloads:

EtherCAT Servo Motor Kit Wiring Diagram (1568 downloads)

MyPlasma CNC Controller,  THC torch height control - Free software

Following items are included:

USB controller, plasma interface, and a USB cable

Basic functions of the program / Controller:

1. Max range of the machine: No restrictions
2. The minimum pulse width Step Auto
3. STEP signal max frequency: 350kHz
4. Integrated height adjuster THC: Yes
5. Function anti-dive burner: Yes
6. Detection of material: Yes Touch / Floating head
7. Operation Collision Sensor: YES
8. Types of accepted files: DXF, PLT (HPGL), G-codes (.tap)
9. Integrated CAM: Yes, CAM MyMini
10. Wen automatic object recognition. Ext. : YES
11. Analysis of the path ahead: YES
12. Base cutting parameters: YES
13. Correction angle to the material design: YES
14. Operation using GamePad controller: YES
15. Can be cut from anywhere: YES
16. Can be cut from the end: YES
17. Supported Controllers CNC: CNC MyPlasm
18. Operation controllers and motherboards from other manufacturers: NO
19. Ability to work through the LPT port: NO
20. Import DXF, PLT or G-CODES
21. Automatic generation of offset paths, entrances and departures
22. The program can be used with an external CAM program
23. Separate speeds hole
24. base parameters
25. Correction of the project to the angle of the material
26. Soft and Hardware Limits
27. Functions THC antynurkowania
28. Możliwaość Game Control Pad
29. Detection of material through the touch system, a floating head or both.

Installation Manual :

Click for Installation Manual

Wiring Diagram:

Proma MyPlasma Controller Wiring Diagram (2529 downloads)

Download Software and Instructions:

Click to Download Software

Video:

Click to Check the Video

**If software shows "Connection Error": first check if the power supply is 24V. If yes, hold SHIFT key and "Click to Rest" in software for updating the firmware.**

Read the rest of this entry »

The control systems can be widely applied to machinery, advertisement, woodworking, Jade carving, mold engraving machines, laser, flame, plasma cutting machines, woodworking lathe, dispensing machine and so on in the industry machine control field.

DSP is the core control system, High-speed processing operation which the microcontroller and PLC systems can’t compare with. Embedded structure, high degree of integration, Strong stability, easy to installation and operation; support U disk, removable storage card reader, with USB interface, high speed transfer, plug and play. Fully offline work.

The control system contains the following parts:

1. 1pc Handheld controller
2. 1pc I/O board
3. 1pc 19-pin HDMI data transmission cable
4. 8GB USB flash drive

Features:

• 5 inch color screen, support tool path simulation and G code display during processing
• Supports 8 tools, tool track location can be customized
• New technology if tool change and tool setting method, greatly improve the efficiency of tool setting process
• Identify tool change T instruction, support multiple tool changing
• Detection mechanism such as tool holding, tool magazine in place, hard limit etc. Ensure security of the operation
• Support tool change spindles
• System parameters can be backed up to external storage space in file format
• Extensive application of mechanical engraving filed, such as advertising, woodworking, and stone carving machine

Wiring Diagram:

B57-Stepper Board Wiring Diagram (936 downloads)

B57-Servo Board Wiring Diagram (913 downloads)

User Manual:

B57 Motion Control System User Manual (1281 downloads)

Acorn Plasma CNC control kits are both a CNC Hardware and CNC Software DIY system designed to work together for easy CNC setup and operation with minimal fuss.

A reliable, high performance, industrial quality Plasma CNC controller with a real time closed loop Torch Height Control at a do-it-yourself price. Acorn utilizes an integrated 1Ghz ARM Cortex A8 Motion Control CPU and communicates with CNCPC via a fast and reliable Ethernet connection. The Acorn CNC control board controls a wide variety of axis motors and drives with industry standard step and direction command signal. Compatible with AC Servo motor drive packages as well as Stepper motor drives. The Acorn CNC controller runs on Centroid's proven industrial quality CNC control software.

if you need need the Acorn Plasma CNC Control kits, you need to order following items:

Acorn CNC controller kit ( if you do not have it)+Centroid Acorn Torch Height Controller (THC) kit + Acorn Plasma "Pro" CNC Software license or Acorn Plasma "Ultimate" CNC12 Software license , CENTROID Wireless MPG CNC control pendant is a plus

1: Acorn CNC controller kit :
Centroid Acorn CNC controller kit (part # 14455) includes:
- Acorn CNC control board
- Acorn Plug and Play Relay Relay Module
- Dual power 5 VDC and 24 VDC logic power supply
(50/60 Hz 100-120 VAC OR 208-240 VAC input power)
- Logic power supply hookup leads
- 110 VAC power cord
- 15’ Shielded Ethernet cable
- Centroid CNC12 "Free" CNC Mill and Lathe software download
- Touch Screen Responsive Operator Controls

2: Centroid Acorn Torch Height Controller (THC) kit:
includes:
- THC TX control board
- THC RX control board
- 5' Fiber Optic Cable ( TX to RX connection)
- 12" Shielded Serial Cable M/F Straight ( RX-to-Acorn connection) Note: 18" and 36" can be purchased here
- Din Rail Mount 24 volt power supply

Requirements:

- Acorn CNC controller kit (Acorn requirements are here)
- A Hypertherm Powermax Plasma Cutter or Lincoln Flex Cut! (see FAQ's below)
- An Acorn CNC12 Plasma Pro software license (purchase below)

3: Acorn Plasma "Pro" CNC Software license :

- Restart Mode, backup along part contour and start anywhere
- Torch Check
- Dry Run
- Material Profile Manager
- Smart Sense
- THC Anti Dive controls
- Plasma Smoothing
- Unlimited G-code file size
- 4th axis G-code moves
- Six WCS locations (G54 thru 59)
- All features of the CNC12 Free are included
After purchase, the License will be sent via E-mail
Each Acorn Software License is specific to a single Acorn board.
If you are purchasing a license for a previously ordered Acorn kit please email a fresh report.zip file to us.

4: Acorn Plasma "Ultimate" CNC12 Software license:
- Unlimited Plasma Intercon conversational programming (now available in beta)
- Includes both a "on the cnc control" copy and a offline "on any Windows PC" copy
- Unlimited Teach Mode
- USB Key allows running of Intercon Plasma on any Windows PC
- All features of the CNC12 Free and Pro are included
- Any future Plasma Features

5: CENTROID Wireless MPG CNC control pendant
Model: WMPG-4 for Acorn CNC equipped Plasma machines :

Take the control to where the work is! A game changing tool, the Centroid Wireless MPG handwheel CNC Control pendant allows the operator to conveniently and precisely set up jobs and tools remotely. No software or drivers to install. Plug and Play with Centroid CNC12 Pro CNC software, just plug in the included USB transmitter/receiver and start using it

• Use the MPG Wheel to Jog the machine for any kind of positioning.
• Smooth motion
• Sensitivity of the wheel detents are adjusted by the x1,x10,x100 selector.
• Use the MPG Wheel to control the cutting Feedrate on the fly.
• Use the MPG Wheel to control the Target Voltage on the fly.
• 4 axis DRO display
• 4 axis MPG and continuous jogging control
• Robust wireless communication
• No software drivers to install
• Hanger bracket mount w/ magnets
• Long range wireless
• Robust CENTROID developed drivers
• Takes 2 AA batteries, run time approximate 1 month
• USB Plug and Play Transmitter / Receiver
• Rubber case protector
• Tactile Feedback domed buttons w/ gold contacts
• High quality 3M Overlay

Pls check this Video:

2: CORE

A step up for makers and workshops looking for more flexibility and multi-axis power.

Building on the Essential tier, the Core model expands your capabilities with 5-axis motion control, probing, MPG support, and closed loop motor feedback for enhanced control. It adds advanced spindle and laser control, plasma multi-head with DTHC support, and comprehensive coolant management. With Wi-Fi connectivity to your PC, cloud, and mobile app, plus features like auto tool zero and manual tool change alerts, this tier is ideal for makers ready to move beyond the basics and take on more complex projects with greater precision and confidence.

You get everything in Essential, plus:

• 5-axis motion control with slaving
• Wi-Fi with PC, cloud and phone app connectivity
• Manual tool change with message and alert signal
• Auto tool zero
• Tool setter support
• Probing options
• MPG (manual pulse generator) support
• Advanced Spindle RPM Control (VFD, PWM & STEP)
• Laser control for engraving
• Plasma multi-head with Digital Torch Height Control (DTHC) support
• Closed loop motor feedback control
• Parking Offset

Ideal For

• Experienced makers
• Custom shops
• Small batch production
• Makers needing more
  precision and automation-
  ready features

Key Features

5-axis control, probing,

advanced spindle control,

laser features, and cloud

connectivity.

Raytools BM110-FC 2D AutoFocus Fiber Laser Cutting Head

Rated Power: 2.2KW

Rated Voltage: 220V

Rated torque: 1.17Nm

Rated Speed: 18,000rpm

Maximum Speed: 24,000rpm

Rated Frequency: 300Hz

Maximum: Frequency: 400Hz

Cooling Method: Air-cooled

Lubricating Method: Grease

Tool Holder: ISO20

Tool Cone: ISO20

Pull Stud: ISO20-15

Weight: 8.9kg

Download:

KL-2200AATC Drawing (179 downloads)

KL-2200AATC User Manual (167 downloads)

KL-2200ATC Automatic Tool Changer:

Tool Holder: ISO 20

Pull Stud: 15 Degree Angle

Diameter: 80mm

Length: 353 mm

Speed: 24000 rpm

Cooled: Water Cooled

Pneumatic controlled

Temperature control：22-25℃

Frequency:  800Hz

Voltage: 220V

Weight: 9 kg

Specification:

KL-2200W ATC Spindle Drawing (677 downloads)

Air Supply:

ATCAirDescription (1428 downloads)

2.2kw spindle ATC Wiring

Spindle Power

U- Red

V- Yellow

W- Brown

2x brown wires - Temp protector

Loading Tool Sensor

Brown-   +24VDC

Blue-       0VDC

Black-     +Signal

Unloading Tool Sensor

Brown-   +24VDC

Blue-       0VDC

Black-     +Signal

Spring Pressure to hold tools: 80Kg

Recommend VFD for this spindle:

KL-VFD05A Mini-type Integrated Universal Inverter (VFD), 2.2KW, 1000HZ

KL-4500ATC

4.5KW 220V 24000rpm

800Hz 15.5A

Cooled: Water Cooled

Pneumatic controlled

Temperature control：22-25℃

Pole: 4 P

1 or 3 Phase

Drawing Download:

KL-4500W ATC Spindle Drawing (676 downloads)

Application

Woodworking engraving machine, woodworking CNC.

Widely used in wood engraving, plastic engraving and other fields.

Recommend VFD for this spindle:

4.5KW 6HP VFD Inverter 1phase 220V, 1000Hz

3/4 Axis NEMA 34 Closed Loop Stepper Motor Controller 110VAC/220VAC

It works with Mach3 and Mach4

Pls email us, this is just a typical sample application, we can make as you need

FEATURES:

1:  1pcs Controller Box

BX4 - 600 x 400 x 250 mm Enclosure Box with side panel

2: 1pcs C82 Breakout Board

C82 - Dual Port Multifunction Board

3: 1pcs  6 Axis Ethernet SmoothStepper Motion Control Board

Connection to a PC.  Runs with Mach3 or Mach4 on Windows 32 or 64 bit.

Ethernet SmoothStepper Motion Control Board for Mach3 and Mach4

4: 3/4 pcs Closed Loop Stepper Motor and Driver

NEMA 34 Closed Loop Stepper Motor System-Hybrid Servo Kit:  1699 oz-in 1/2'' Shaft Size

6: 1pcs  24V/2A  power supply

24V/2A Switching CNC Power Supply 

8: Miniature Circuit Breaker, 32A

8: Power cord

9: E-Stop and Power Switch

If  you need 3 /4 Axis Inductive Switch Assembly to RJ45, click here to purchase:

3 Axis RJ45 limit switch or 4 Axis RJ45 limit switch

One Year Warranty

EtherCAT Servo Motor Control System with Mach4, 750W , 3 Axis

AC 110V, No Power Supply, No Breakout Board,  Easy to wire

Following Items  are included

( Computer is not included):

--1 pcs EtherCAT Motion Controller, Working with Mach4 ( with Relay and Spindle Control)

EtherCAT Motion Controller, Working with Mach4

-- 1pcs Mach4 Software

Fully Licensed versions of Mach4, Email you the license.

--3 Pcs EtherCAT Servo Motors  750W

-- 3 Pcs EtherCAT Servo Driver , 190-230VAC

Cable-7BMA5M0-Z "5-Meter encoder cable with battery"

CABLE-RZ5M0-S - 5-Meter power cable

EtherCAT Servo Motor Kit, 750W 220VAC (750W EtherCAT kits with 5meter cable)

If you  need 3 Meter cable, pls let me know. (Cable-7BMA3M0-Z "3-Meter encoder cable with battery" ,  CABLE-RZ3M0-S - 3-Meter power cable)

-- 3 Pcs Proximity Switch with 1.5 Meter Cable

Inductive Proximity Switch,NPN

-- 1 Pcs E - Stop with 1.5 Meter Cable

E-stop Switch

-- 1PCS 12Vdv Power Supply for the limit switch

Switching Power 12V/5A 110V/220VAC

We can configure 4 Axis, 5 Axis, 6 Axis ..... to N axis

We can change from 1.5-meter cable to other Length as you need

Motor and Spindle Control Testing Video:

(Need to purchase the analog output expansion along with the controller board for spindle control, the expansion is not includes in this kit)

Video:

Servo kits with EtherCAT motion Card Testing video

Downloads:

EtherCAT 750W AC Servo Motor Drawing (984 downloads)

EtherCAT Servo Driver User Manual (1958 downloads)

EtherCAT Servo Motor Kit Wiring Diagram (1568 downloads)

XML File for EtherCAT Servo Driver (1070 downloads)

FSCUT2000E medium power laser cutting system is for 1000-4000W power laser cutting scenarios. It is easy to install and debug with excellent performance and complete solution.

Technical Data:

• Condition: Brand New
• Model: MFSC-2000W
• Power: 3000W
• Operating power: Three phase, AC200-220V, 50/60Hz

The new generation of Single Module 2000W Fiber Lasers which combined with high power, compact size, superior beam quality, and high light conversion efficiency. It can meet the requirements of precision processing, 3C product welding and high-reflective material cutting ability are significantly improved. It is suitable for remote processing, high-frequency laser cutting and clean surface cutting. It can be quickly and conveniently integrated into machine tool equipment and large-scale factory automation production line.

1. More reliable and saving power.

2. Easy to maintain.

3. Easy to operate.

• Condition: Brand New
• Model: MFSC-3000C
• Power: 3000W
• Operating power: Three phase, AC200-220V, 50/60Hz

The new generation of Single Module 3000W Fiber Lasers which combined with high power, compact size, superior beam quality, and high light conversion efficiency. It can meet the requirements of precision processing, 3C product welding and high-reflective material cutting ability are significantly improved. It is suitable for remote processing, high-frequency laser cutting and clean surface cutting. It can be quickly and conveniently integrated into machine tool equipment and large-scale factory automation production line.

1. More reliable and saving power.

2. Easy to maintain.

3. Easy to operate.

]]>

690-90W, Brand New Laser Engraving Machine, You can come to our show room to check in Chicago

• Click to apply Financing

or call me at 847-984-0882

Following Item are included

1: Honeycomb Table

2:Water Chiller, CW3000

3: Exhaust Fan

4: Air Assist with Compressor

5: Auto Focus

6: Automatic Z Table, Full up/down table

7: Red Dot Point

8: Ruida 6442G Controller

Ruida 6442G Controller

Specifications:

Laser Power: 90W,  Min 80W, Max 100W

Work Area: 890 mm x 610mm, 36”x24”

Full Machine Size: 1480 x1060 x 1080 mm, 59”x 42”x 43”

Driving System: Stepper Drives

Vertical Z Travel of Table:  about 8 inch

Cooling Mode: Water Cooling with Flow Protection

Controlling Software: DSP Control System, LaserWork

Compatible Software: CorelDraw, AutoCAD, Photoshop

Supported Graphic Format: BMP, JPG, PLT, DXF, AI

Engraving Speed: 0-54,000mm/min

Working Voltage: 110VAC

Net Weight: 185kg/410lbs

Packing size: 65" x 54" x 54"

Is the Z axis a stepper motor or DC: 2 phase stepper motor

Color Blue

One Years USA Part Warranty

3 Month co2 laser tube warranty

1. Applicable materials:

Cloth, leather, fur, acrylic, plexiglass, wooden board, plastic, rubber, bamboo, product, resin and other non-metal

2. Applicable industries:

The machine is suitable to cutting of garment and leather, package and

printing, advertisement decoration, building upholster art gift, computer embroidery, paper product, acrylic board etc.

Connect the machine to ground, do not forget

We will charge the actual shipping fee because the website can not calculate

We will send you a PayPal request for shipping fee difference

Machine color or style may vary.

Machine Wiring: 

80w-Machine-Tube-and-Software-installation (2234 downloads)

Installation-of-Laser-Tube (1730 downloads)

Laser-Tube-Usage (1828 downloads)

RDCAM-Software-SetUp-Manual (2741 downloads)

Connection Settings with your Desktop/Laptop:

Machine Wiring:

Laserwiring (2128 downloads)

USB or Ethernet Connection:

Laser Machine Connection Setup (1899 downloads)

Laserwork Software

• This is a video from youtube

Check out the video below if there is no fire from the laser tube

(Be careful and protect yourself from the high voltage while testing!!)

Some common products include CerMark, Enduramark, and LaserBond – allow it to dry, and then perform the engraving as normal. The heat from the laser bonds the solution to the metal, resulting in a permanent black, silver, or sparkle-type mark from a CO2 laser machine.

You can come to our show room to check the machine.

• Click to Apply Financing

This machine runs at 220VAC. If you have 110Vac, you need to buy  a step-up transformer, 110VAc to 220VAC ,  3000 Watt Step Up/Down Electrical Power Voltage Converter Transformer

• Brand New CNC Router Engraving Machine with USB Connection
•  2.2KW (3HP) Liquid Cooled Spindle + 2.2KW Variable Frequency Driver
• We Changed this Machine to Mach3 Controlled System.
• Working Size X,Y,Z : 650(x) 900 (y)  200mm(Z) ( about 26" x 36 " x 7.87")
• Gantry Height: 200mm (7,87 inch)
• Working Speed : 200 -300 IPM, Rapid Speed: 500 IPM
• Resolution: about 0.05 mm, X, Y, Z Repeatability: 0.02 mm
• Mach3 Controller with Mach3 Demo Software (Mach3 License file is not included)
• Spindle: 2.2KW, Water-Cooled, ER20 collet chuck
• Water Pump With Tank
• Spindle Speed: 6000-24000rpm with VFD, AC220V/50Hz/60HZ
• X, Y, Z axis driver: Stepper Motor Driver, NEMA34 Stepper Motor, 640 oz-in
• X, Y Z Limit Switch, E-Stop
• 6 axis USB Breakout Board, you can use at 32, 64 bit computer, Window 10, 8, 7 , XP
• 20 Taiwan Hiwin Rail and Guider
• Wood Packing Size: 59 x 51 x59 inch

Weight: 950 lbs

One Year USA parts warranty

2: If You need a MPG, pls check here

• Mach3 Wireless MPG

Start Up Procedure:

KL-Series CNC Manual (5960 downloads)

KL-6090wiring (2770 downloads)

You can add mach3, Mach4 or Computer

Fully Licensed Mach3 (Authorized), Email you license file

Fully Licensed versions of Mach4, Email you the license.

I5 CNC Computer with 19" monitor, Refurbished

847-984-0882  /  automationtecinc@yahoo.com

• Click to Apply Financing

Brand New CO2 Laser Engraving Machine, 130 W RECI Tube, KL-1390

One Year USA support and one year part warranty

Following Items are included

1: Honeycomb

2: Water Chiller: 5000W

3: Air Assist with Compressor Included

4: Exhaust fan

5: Motorized Z table: Up/down

6: Red Point

7: Laser Software license included

Specification:

Color: Blue/White or Gray/white

Laser- type：Sealed CO2 laser tube

Laser power: Max 150W

Motorized Z table

Cutting area:1,300 x 900 mm About 51" x 36"

Whole machine size:1,720x 1,210 x1,070 mm ( 67.7 inch x 47.6 inch x 42.1 inch)

Wood Packing Size: 79 inch x 76 inch x 51 inch

Cutting speed: 0 -600 mm/s

Resetting positioning accuracy: ±0.05mm

Working voltage: AC 110V±10%, 50 - 60Hz

Gross power: <1,200W

Operating temperature: 0 - 45℃

Operating humidity: 5- 95%

Graphic format supported: BMP,PLT, DST, DXF, and AI

Cooling mode: water-cooling and protection system

Compatible software: CorelDraw AutoCAD Photoshop

Net Weight：420kg

Machine Wiring:

Laserwiring (2128 downloads)

USB or Ethernet Connection:

Laser Machine Connection Setup (1899 downloads)

KL-1313 CNC Router 51" x 51" x 11.0", with Mach3 or Mach4 control, or UCCNC

 T slot, Vacuum Table, Helical Rack and Pinion

Click to Apply Financing

Pls contact us to quote the shipping fee according your address

1: KL-1313 CNC Router ~51" x 51" x 11 ", It has  T-slots and Vacuum Table, helical rack and pinion in X, Y axis, It has Mach3 spindle and relay control board with USB Connection, you can use 32bit or 64 bit computer

Machine with 3.2W Water Cooled Spindle + 3.2KW 400Hz Variable Frequency Drive, 6000-24000 RPM

ER20 Collet Chuck

Working Size X,Y,Z : 1300 x 1300 x 270mm ( about 51" x 51" x 11")

NEMA34 Stepper Motor and Driver: 495 oz-in, 6A with 5:1 Pulley Reduction

Automatic Lubricated System

Resolution: about 0.05 mm

X, Y, Z Repeatability: 0.02 mm

Working Speed : 100 -500 IPM

Rapid: 500-800 IPM

X, Y, Z axis Stepper Motor Driver: High Quality Stepper Motor Driver

X, Y, Z Optical Switch

E- Stop, Z Height Probe

Machine Weight: About 1500 lbs

One year USA parts warranty

You can come to our show room to check the machine.

USA Tech Support Phone: 847-984-0882

• Click to apply with leasestation.com

• Click to apply with trilease.net

2: You can run the router at 110VAc or 220VAC with a step-up transformer, from 110VAC to 220VAC ( Transformer is not included)

• 3000 WATT VOLTAGE CONVERTER TRANSFORMER

3: We use this Ethernet Board: Mach3 or Mach4 ESS board

4: a Wireless MPG is not included, pls check here

• MPG Handwheel Control Pendant for Mach4 and Mach3 ( P1A-S)

Start Up Procedure:

KL-1313 and KL-1325 Installing Guide (1213 downloads)

KL-Series CNC Manual (5960 downloads)

KL-1212wiring (1301 downloads)

You can add mach3, Mach4 or Computer

Fully Licensed Mach3 (Authorized), Email you license file

Fully Licensed versions of Mach4, Email you the license.

I5 CNC Computer with 19" monitor, Refurbished

You can use this lubrication Oil Mobil Vactra #2 Way Oil (1 Gallon)

SampleVideo:

KL-1313 Customer Video

Compact Precision Metal Cutting | Sheet Metal Fabrication | Small-Batch Customization

Product Overview

The Desktop 800W Fiber Laser Cutting Machine is a compact, highly integrated metal-cutting solution designed for precision sheet metal fabrication, small-batch production, prototyping, and customized manufacturing.

Featuring an 800W Raycus air-cooled fiber laser source, Ruida control system, and Leadshine motors, this machine combines reliable performance with a space-saving design.

Its semi-enclosed structure, movable box-style worktable, and integrated ventilation make it suitable for workshops, factories, design studios, educational institutions, and makerspaces.

Key Features

1. Compact & Space-Saving Design

Lightweight, compact, and highly integrated, making it ideal for limited workspaces and flexible production environments.

2. Semi-Enclosed Structure – Stable & Durable

The semi-enclosed design provides a protective barrier around the cutting area while allowing convenient access for operation and maintenance.

3. Movable Box-Style Worktable

Flexible worktable design supports convenient material handling, cutting operations, and customized fabrication tasks.

4. Advanced Ruida Control System

Equipped with a Ruida control system, compatible laser cutting head, and control software for convenient operation and cutting process management.

5. 800W Raycus Air-Cooled Fiber Laser Source

Features an 800W Raycus fiber laser source with air cooling, eliminating the need for a separate water chiller under the manufacturer's specified operating conditions.

6. Leadshine Motor System

Uses Leadshine motors for controlled machine movement and consistent positioning.

7. Integrated Ventilation & Smoke Extraction

Features an observation window and integrated ventilation system designed to assist with the removal of smoke, dust, and heat generated during cutting. Appropriate external exhaust and filtration may still be required.

Technical Specifications

Applications

• Sheet Metal Fabrication: Small hardware components, metal panels, equipment enclosures, and cabinets.

• Automotive & Motorcycle Parts: Customized brackets, panels, and precision components.

• Industrial Manufacturing: Tooling fixtures, equipment components, and prototype parts.

• Electronics & Precision Engineering: Small precision metal components and customized assemblies.

• Home & Architectural Hardware: Kitchen and bathroom hardware, architectural models, and decorative metalwork.

• Creative Manufacturing: Metal crafts, nameplates, jewelry components, and customized designs.

• Education & Research: Technical training, makerspaces, laboratories, and academic teaching.

• Small-Batch Production: Prototyping, on-demand fabrication, and low-volume customization.

Main Selling Points

Recommended Marketing Tagline:

“Compact Size. Precision Metal Cutting. Built for Custom Manufacturing.”

Machine Specification:

lasermachine (33 downloads)

BRAND NEW 130W–150W CO₂ LASER ENGRAVING & CUTTING MACHINE – 1512

IN STOCK NOW – READY FOR SALE!

Call for Pricing & Availability: 630-254-8655

Brand-new industrial CO₂ laser engraving and cutting machine featuring a large 60" × 48" working area, RECI laser tube, motorized Z-axis table, autofocus, and Ruida RDL6442G controller.

Ideal for businesses, sign shops, engraving professionals, fabrication workshops, and custom manufacturing applications.

INCLUDED ACCESSORIES

1. Honeycomb Worktable
2. CW5200 Water Chiller
3. Air Pump
4. Exhaust Fan
5. Autofocus System
6. Motorized Power Z Table
7. Red Dot Pointer
8. LaserWorks Software License
9. Automatic Up/Down Table
10. Ruida RDL6442G Controller

TECHNICAL SPECIFICATIONS

KEY FEATURES

• Large-format engraving and cutting capability
• Powerful RECI CO₂ laser tube
• Ruida DSP controller for precise operation
• Automatic focus for convenient setup
• Motorized Z-axis worktable
• Integrated air-assist and exhaust accessories
• CW5200 water-cooling system
• Red dot positioning for easier alignment
• LaserWorks software license included

COMMON APPLICATIONS

Suitable for engraving and cutting compatible nonmetal materials such as acrylic, wood, plywood, MDF, leather, fabric, paper, cardboard, and other laser-compatible materials.

Excellent for signage, personalized gifts, decorative panels, architectural models, custom displays, craft production, and industrial engraving.

Machine Wiring:

Laserwiring (2128 downloads)

USB or Ethernet Connection:

Laser Machine Connection Setup (1899 downloads)

• Click to apply Financing

Pls contact us to quote the shipping fee according your address

We opened and checked, tested in our Chicago office

We paid the duty and broker fee.

You can come to our show room to check the machine. or call us at 847-984-0882 for any question. You do not need anything to start up your job

USA Tech Support: 847-984-0882

1:  Brand New CNC Router Engraving  Machine ,T slot, Vacuum Table, Rack/Pinion

2: 3 .2 KW Water Cooled Spindle + 3.2 KW 400Hz Variable Frequency Driver

3: We changed this Machine to Mach3 or 4 Control , DB25 Breakout board with Relay and  Spindle control with Ethernet,  You can use 32 bit or 64 bit Computer

4: We can update to Centroid Software if you  need

4:  Mach3 Software  is not included

Spindle Power Motor: 3.2KW, Water-Cooled, ER20 Collet Chuck

Spindle Speed: 6000-24000 rpm With VFD, AC220V/50Hz/60HZ

X, Y, Z axis driver:  Stepper Motor Driver, NEMA34 Stepper Motor

X, Y Z Limit Switch

E- Stop, Z Height Probe

X Axis:   Rack Pinion Modulus: 1.25 mod

Y Axis: helical rack and pinion (Modulus: 1.25 mod) with pulley reduction 4:1

Z Axis 20m Linear Rail with 25mm Ball screw, 10mm lead

Spindle speed: 6000 to 24000 RPM

Table Grid Size: 8mm x 8mm

Each panel has a Valve to Control  "ON/OFF"

One year USA parts Warranty

We will send you a PayPal request for shipping fee difference

Size of packing: W86"  x H 71" x L 129"

Total weight: 1850 Lbs

Start Up Procedure:

KL-1313 and KL-1325 Installing Guide (1213 downloads)

KL-Series CNC Manual (5960 downloads)

KL-1212wiring (1301 downloads)

You can add mach3, Mach4 or Computer

Fully Licensed Mach3 (Authorized), Email you license file

Fully Licensed versions of Mach4, Email you the license.

I5 CNC Computer with 19" monitor, Refurbished

You can use this lubrication Oil Mobil Vactra #2 Way Oil (1 Gallon)

Product Description:

• The machine is welded with cast iron structure, the stability is excellent, not easy to be deformed.
• Three-axis adopted ball screw and linear orbit, stable working, high precision, and long using life.
• Good compatibility: CAD/CAM designing software e.g. Type 3/Artcam/Castmate/Wentai etc.
• High precision, curving, and linear speeds are consistent.
• 2.2kw ATC water cooling spindle, with high precision and strong power. There is a cover to protect the spindle. Extended service life, keep clean, and protect the operator's safety.
• It is equipped with the international DSP B58 control system, which could memorize the breakpoint.
• With MDF T-slot working table, holding the materials with clamps, you can do a variety of high-precision works.

One Year Parts Warranty

We will ship from the factory

Product Description:

• working area 1300 *2500*200mm
• Taiwan TBI Ballscrew transmission for Z axis
• Helical Rack and gear for X,Y axis
• Dust cover for X axis
• Taiwan Hiwin linear square guide
• Leadshine Hybrid servo motor and driver
• Shimpo reducer
• Sifang inverter 4KW
• Weihong NK105 control system
• 3.2 Kw ATC JianKen water cooling spindle
• 8 pcs ATC under gantry
• Vacuum table with T slot without air pump
• Automatic tools sensor
• One box tools (10 pieces)
• Power supply 48V,12.5A

Specification:

• XYZ working area: 1300*2500*200mm
• Table size: 1310*3000mm
• XYZ travel positioning accuracy: ±0.025mm
• XYZ repositioning positioning accuracy: ±0.025mm
• Table surface: Bakelite sheet
• Gantry: steel
• Drive system X-Y axis: Rack actuation
• Drive system Z axis: Ball screw
• Spindle power: 3.2 KW ATC water cooling spindle
• Max velocity: 25m/min
• Max working speed: 15m/min
• Spindle speed: 0-24000rmp
• Work mode: Stepper motor
• Working voltage: AC220V
• Command language: G code
• Interface: USB
• Operating system: NK105
• Flash memory: 128
• X-Y resolution: ﹤0.025mm
• Software environment: Wentai type3 artcam
• Running environment: Temperature:0-45℃
• Packing size: 3300*1900*190mm
• Net weight: 1300kg
• Gross weight: 1500kg

One Year Parts Warranty

We paid the duty and shipping fee to USA

Max 1500 W fiber laser source, air cooled

FG120 Fully Enclosed Lead Screw Module

Machine working area: 1000 x1000 mm ( 39" x 39" )

Accuracy: ±0.05 mm

Leadshine 400 W Servo Motor

High-flexibility Servo cable

Raytool laser cutting head

Raytool laser cutting control system

Sheet-metal machine enclosure and electrical control cabinet

Upper protective enclosure / cover

Fully assembled and tested; ready for shipment

One year warranty

INDUSTRIAL FIBER LASER METAL CUTTING MACHINE

5 × 10 FT Working Area | Up to 3000W Laser Power

Larger 5 × 20 FT Model Available – $48,000

PRICE INCLUDES IMPORT DUTIES AND SHIPPING TO YOUR DOOR!

We offer high-performance fiber laser metal cutting machines designed for precision, efficiency, and reliability.

Our machines are suitable for sheet metal fabrication, industrial manufacturing, metalworking shops, and custom metal cutting applications.

DELIVERY, INSTALLATION & SUPPORT

• All-Inclusive Delivery: Price includes machine cost, import duties and shipping directly to your address.
• Easy Unloading: You only need to arrange a forklift to unload the machine upon delivery.
• Machine Testing: We can set up, test, and demonstrate machine operation before shipment in factory.
• Professional Training: Operator training is available in factory.
• USA Technical Support: Dedicated support from qualified technicians and engineers based in the United States (optional).

CUTTING CAPACITY BY LASER POWER

Cutting thickness in millimeters (mm). Actual performance depends on material grade, assist gas, cutting parameters, and desired edge quality.

TECHNICAL SPECIFICATIONS

INCLUDED CONSUMABLES & ACCESSORIES

• 30 Cutting Nozzles
• 25 Protective Lenses
• 5 Ceramic Rings
• Transformer – 40kVA
• Voltage Stabilizer – 50kVA
• Hanli Water Chiller
• Oxygen and Nitrogen Proportional Valves

APPLICATIONS

• Industrial Sheet Metal Fabrication
• Carbon Steel and Stainless Steel Cutting
• Aluminum and Brass Fabrication
• Automotive and Machinery Components
• Metal Cabinets and Equipment Enclosures
• Custom Metal Parts Manufacturing
• Architectural and Decorative Metalwork
• Prototype and Production Cutting

WHY BUY FROM US?

Factory-Ready Equipment: High-quality components from recognized manufacturers, including BoChu, Leadshine, MOTOVARIO, and Hanli.

Delivered to Your Door: Import duties and freight included in the quoted machine price.

Tested Before Delivery: Machine setup, testing, and demonstration can be arranged before shipment or pickup.

USA-Based Technical Support: Our qualified technicians and engineers are available to assist with machine operation and technical questions.

Training & Installation Available: We can also provide operator training and installation services.

CONTACT US FOR A QUOTE

5 × 10 FT Model: Email us for pricing.

5 × 20 FT Model: $48,000

Call: 630-254-8655

Email us today for additional details, availability, and a formal quotation.

Warranty: One Year Parts