posted by | on | Comments Off on NEMA34 110AC Closed Loop Stepper Motor, Driver,Hybrid Servo Kit,1699 oz-in Shaft 14mm

 

NEMA34 110AC Closed Loop Stepper Motor 1699 oz-in, Driver – Hybrid Servo Kit:

1pc NEMA 34 Closed Loop Motor: KL34-12N-1000:  1699 oz-in, shaft size: 14 mm ( Not 1/2)

1pc 110VAC KL-110-80H Driver

1pc Cable, 1.5m or longer

Specification:

1: NEMA 34 Closed Loop Motor: KL34-12N-1000:  1699 oz-in, shaft size:  14 mm ( Not 1/2)

Specification:

Current: 5A

Holding Torque: 12 N-m, 1699 oz-in

Encoder on back: 1000 line

Phase Inductance: 12 mH

2: 110VAC KL-110-80H Driver Specification

Closed-loop control, no longer lose any steps,

Up to its maximum torque;

Higher torque and higher speed;

Fast response;

Reduced motor heating and more efficient;

Zero-speed stability;

Smooth motion and super-low motor noise;

No Tuning and always stable;

Lower cost

Wiring:

A+ to Black

A- to Red

B+ to Yellow

B- to Blue

Downloads:

KL34-12N-1000 Datasheet (221 downloads) KL-110-80H Datasheet (445 downloads) KL-110-80H Hardware Manual (455 downloads) NEMA34 Closed Loop with C10 Wiring Diagram (396 downloads)

If you need the RS232 Tuning Cable for Driver: RS232Cable

RJ45 Ethernet Connector for Driver: ES-DH Connector 

Process to reset your driver to factory setting:

  1. Press” ENT”, then press “M” switch the screen till it shows “AD-lnl”
  2. Press “ENT”, the screen change to “lnl”
  3. Press the Up arrow bottom till the screen shows “Finish”.
  4. Power cycle the driver.

posted by | on | Comments Off on NEMA34 Closed Loop Stepper Motor System- Hybrid Servo Kit-32 bit DSP Based, 1128 oz-in

 

NEMA 34 Hybrid Servo kit (closed-loop stepper system):

1pc Hybrid Servo Driver KL-8082H,

1pc NEMA34 KL34-8N-1000 Hybrid Servo Motor with one Encoder 1000 line,

1pc 1.5 meter cable or longer

Specification:

A: KL-8082H 2-phase Hybrid Servo Driver:

30-80V, 8.2A Peak, No Tuning, Nulls loss of Synchronization

Closed-loop, eliminates loss of synchronization

Broader operating range – higher torque and higher speed

Reduced motor heating and more efficient

Smooth motion and super-low motor noise

Do not need a high torque margin

No Tuning and always stable

Fast response, no delay and almost no settle time

High torque at starting and low speed, high stiffness at standstill

Lower cost

B: NEMA34 Hybrid Servo Motor, KL34-8N-1000, 1/2″ Shaft

Rated Torque 1128 oz-in, 8 N-m, with Encoder 1000 line

C: 1.5 meter Encoder cable

1000 pulses per revolution

Quadrature digital signals: 4000 steps per revolution

4000 / .05 pitch

80,000 counts per unit


Driver Manual Download:

HY-8082H (2580 downloads)

Motor Specification:

KL-34-8N-1000 (533 downloads)

Torque:

Hybrid Servo Motor (14282 downloads)

Specially for Automation Technologies by Leadshine  (OEM)

Thank you Marty for your video to show the Wiring!